|MLA Citation:||Bloomfield, Louis A. "Tape Recorders Home Page" How Everything Works 23 Jan 2018. 23 Jan 2018 <http://www.howeverythingworks.org/prints.php?topic=tape_recorders&page=0>.|
The magnet is part of the system that makes the surface move. Attached to the surface itself is a cylindrical coil of wire and this coil fits into a cylindrical channel cut into the speaker's permanent magnet. That magnet is carefully designed so that its magnetic field lines radiate outward from the inside of the channel to the outside of the channel and thus pass through the cylindrical coil the way bicycle spokes pass through the rim of the wheel.
When an electric current is present in the wire, the moving electric charges circulate around this cylinder and cut across the magnetic field lines. But whenever a charge moves across a magnetic field line, it experiences a force known as the Lorenz force. In this case, the charges are pushed either into or out of the channel slot, depending on which way they are circulating around the coil. The charges drag the coil and surface with them, so that as current flows back and forth through the coil, the coil and surface pop in and out of the magnet channel. This motion produces sound.
To magnetize a screwdriver permanently, you should expose it briefly to a very strong magnetic field. Touching the screwdriver's tip to one pole of a strong magnet will cause some permanent magnetization. Rubbing or tapping the screwdriver also helps to free up its domains so that they can align with this external field. But the better approach is to put the screwdriver in a coil of wire that carries a very large DC electric current.
The current only needs to flow for a fraction of a second—just long enough for the domains to align. A car battery is a possibility, but it has safety problems: it can deliver an incredible current (400 amperes or more) for a long time (minutes) and can overheat or even explode your coil of wire. Moreover, it may leak hydrogen gas, which can be ignited by the sparks that will inevitably occur while you are magnetizing your screwdriver.
A safer choice for the current source is a charged electrolytic capacitor—a device that stores large quantities of separated electric charge. A charged capacitor can deliver an even larger current than a battery can, but only for a fraction of a second—only until the capacitor's store of separated charge is exhausted. Looking at one of my hobbyist electronics catalogs, Marlin P. Jones, 800-652-6733, I'd pick a filter capacitor with a capacity of 10,000 microfarads and a maximum voltage of 35 volts (Item 12104-CR, cost: $1.50). Charging this device with three little 9V batteries clipped together in a series (27 volts overall) will leave it with about 0.25 coulombs of separated charge and just over 3.5 joules (3.5 watt-seconds or 3.5 newton-meters) of energy.
Make sure that you get the polarity right—electrolytic filter capacitors store separated electric charge nicely but you have to put the positive charges and negative charges on the proper sides. [To be safe, work with rubber gloves and, as a general rule, never touch anything electrical with more than one hand at a time. Remember that a shock across your heart is much more dangerous than a shock across you hand. And while 27 volts is not a lot and is unlikely to give you a shock under any reasonable circumstances, I can't accept responsibility for any injuries. If you're not willing to accept responsibility yourself, don't try any of this.]
If you wrap about 100 turns of reasonably thick insulated wire (at least 18 gauge, but 12 gauge solid-copper home wiring would be better) around the screwdriver and then connect one end of the coil to the positively charged side of the capacitor and the other end of the coil to the negatively charged side, you'll get a small spark (wear gloves and safety glasses) and a huge current will flow through the coil. The screwdriver should become magnetized. If the magnetization isn't enough, repeat the charging-discharging procedure a couple of times, always with the same connections so that the magnetization is in the same direction.
However, there is one big difference between an audio player and a VCR. In an audio player, the tape moves past a stationary playback head. In a VCR, the tape moves past a spinning playback head. When you pause an audio tape player, the tape stops moving and there is no audio signal. But when you pause a VCR, the playback head continues to spin. As the playback head (actually 2 or even 4 heads that trade off from one another) sweeps across a few inches of the tape, it experiences the changing magnetic fields and fluctuating electric fields needed to produce the video and audio signals. That's why you can still see the image from a paused VCR. To prevent the spinning playback heads from wearing away the tape, most VCRs limit the pause time to about 5 minutes.
When you are recording sound on the tape, the microphone measures the air pressure changes associated with the sound and produces a fluctuating electric current that represents those changes. This current is amplified and used to operate an electromagnet in the recording head. The electromagnet magnetizes the tape—it flips the magnetization of some of those tiny magnetic particles so that the tape becomes effectively magnetized in one direction or the other. The larger the pressure change at the microphone, the more current flows through the electromagnet and the deeper the magnetization penetrates into the tape's surface. After recording, the tape is covered with tiny patches of magnetization, of various depths and directions. These magnetized patches retain the sound information indefinitely.
During playback, the tape moves past the playback head. As the magnetic fields from magnetized regions of the tape sweep past the playback head, they cause a fluctuating electric current to flow in that head. The process involved is called electromagnetic induction; a moving or changing magnetic field produces an electric field, which in turn pushes an electric current through a wire. The current from the playback head is amplified and used to operate speakers, which reproduce the original sound.
The rest of the cassette recorder is just transport mechanism—wheels and motors that move the tape smoothly and steadily past the recording or playback heads (which are often the same object). There is also an erase head that demagnetizes the tape prior to recording. It's an electromagnet that flips its magnetic field back and forth very rapidly so that it leaves the tiny magnetic particles that pass near it with randomly oriented magnetizations.
In a video recorder, the tape moves too slowly to produce the millions of the magnetization changes needed each second to represent a video signal. So instead of moving the tape past the playback head, the video recorder moves the playback head past the tape. As the tape travels slowly through the recorder, the playback head spins past it on a smooth cylindrical support. The tape is wrapped part way around this support and two or more playback heads take turns detecting the patches of magnetization on the tape's surface. The tape is tilted slightly with respect to the spinning heads so that the heads sweep both along the tape and across its width. That way, the entire surface of the tape is used to record the immense amount of information needed to reproduce images on a television screen. During recording, currents are sent through the heads so that they magnetize the tape rather than reading its magnetization.
To make a strong permanent magnet, you must find a material that is both intrinsically magnetic and that is able to stay magnetic when it's by itself. Materials that hide their magnetism when alone do this by allowing their magnetic structure to break up into tiny pieces that all point in different directions. Each of these tiny magnetic pieces is called a magnetic domain, and iron and steel are normally composed of many magnetic domains. A good permanent magnet material is one that is intrinsically magnetic and that resists the formation of randomly oriented magnetic domains. A very effective way to make such permanent magnet materials is to assemble lots of tiny magnetic particles. Each of these particles is shaped in a way that makes one of its ends a north pole and its other end a south pole, and that makes it extremely hard for these two poles to exchange places. The particles are then aligned with one another and bonded together to form a permanent magnet. To make sure that the particles all have their north poles at one end and their south poles at the other end, the finished magnet is exposed to an extremely strong magnetic field—one so strong that it flips any misaligned magnetic particles into alignment with the others. After being magnetized in this manner, the permanent magnet is very hard to demagnetize, which is just what you want in a permanent magnet.
The most common magnet materials are Ferrite and Alnico. Ferrite magnets are made from a mixture of iron oxide and barium, strontium, or lead oxide. Alnico magnets are made from aluminum, nickel, iron, and cobalt, and consist of tiny particles of an iron-nickel-aluminum alloy inside an iron-cobalt alloy. But the strongest modern magnets are made from an iron-neodymium-boron alloy. The latter magnets are very resistant to demagnetization and the forces they exert on one another are amazingly strong.
The Tape Recorders Home Page — Printer Friendly
The Complete Collection of Questions about Tape Recorders (4 prints, from oldest to newest) — Printer Friendly: