|MLA Citation:||Bloomfield, Louis A. "Radio" How Everything Works 18 Jun 2018. Page 3 of 4. 18 Jun 2018 <http://www.howeverythingworks.org/prints.php?topic=radio&page=3>.|
Once charge is moving strongly through the resonant circuit in your radio, the radio can monitor various features of that moving charge. If the station is using the AM or amplitude modulation technique to represent sound, your radio studies the amount of charge moving back and forth through the resonant circuit. When that flow of charge—that current—is strong, it moves the speaker cone toward you and produces a compression of the air. When that current is weak, it moves the speaker cone away from you and produces a rarefaction of the air. These changes in air density and pressure reproduce the sound that the station is transmitting.
If the station is using the FM or frequency modulation technique to represent sound, your radio studies the frequency at which charge moves back and forth in the resonant circuit. Very small changes in this frequency, caused by frequency changes in the radio wave itself, are used to control the speaker cone in your radio. When the frequency is raised slightly above normal, your radio moves the speaker cone toward you and produces a compression of the air. When the frequency is lowered slightly below normal, your radio moves the speaker cone away from you and produces a rarefaction of the air. Again, these changes in air density and pressure produce sound.
The waves used for standard AM radio transmissions have very long wavelengths—typically 300 meters—so that they require vertical pole antennas that are about 75 meters long for optimal reception. An antenna of that length is also optimal for radio transmission, which is why the antennas of AM radio stations are so long and slender. However, because such long antennas are inconvenient for most AM receivers, most AM receivers use small magnetic antennas. A magnetic antenna is a device containing an iron-like material called ferrite that draws in magnetic flux lines like a sponge. A coil of wire is wound around this ferrite so that as the magnetic flux lines of a passing radio wave enter the ferrite, they induces electric currents into the coil of wire. This coil then acts as the antenna.
But the waves used in FM radio transmission have much shorter wavelengths—typically 3 meters—so that antennas of about 75 centimeters are all that's needed. The vertical pole radio antenna on your car is designed to receive these FM waves. The antennas of FM radio stations are also rather short, but they are usually mounted high up on a pole so that the whole structure looks like an AM radio antenna. However, if you look near the top of an FM radio tower, you'll see the actual FM antenna as a much smaller structure.
To convey audio information (sound) to you radio, the radio station makes one of several changes to the radio wave it transmits. In the AM or Amplitude Modulation technique, it adjusts the amount of charge it moves up and down its antenna, and hence the strength of its radio wave, in order to signal which way to move the speaker of your radio. These movements of the speaker are what cause your radio to emit sound. In the FM or Frequency Modulation technique, the radio station adjusts the precise frequency at which it moves charge up and down its antenna. Your radio senses these slight changes in frequency and moves its speaker accordingly.
You need only four basic components for a crystal radio: an antenna, a tank circuit, a diode, and a high-impedance earphone.
The antenna is a long wire that projects upward into the electromagnetic fields of the passing radio wave so that electric charges begin to move up and down its length. The ideal length for this wire is a quarter of the wavelength of the wave you're trying to receive, but since that's hundreds of meters for a typical AM station, you'll have to settle for a shorter than ideal antenna.
The tank circuit is a coil of wire that's connected at each end to the two ends of a capacitor. In a typical crystal radio, one of these items—either the coil or the capacitor—is adjustable and forms the tuning element that allows you to select a particular AM station. The tank circuit is a resonant device—electric charges and current flow back and forth through it rhythmically at a specific frequency. If that resonant frequency is adjusted so that it coincides with the transmission frequency of an AM radio station, the small currents flowing in the antenna that's connected to the tank circuit will excite large movements of charge and current in the tank circuit.
The diode is also connected to the tank circuit. Its job is to extract some of the charge that oscillates back and forth in the tank circuit and to send that charge to the earphone. By allowing current to flow only in one direction, the diode samples the overall amount of charge moving in the tank circuit. What it passes to the earphone is a measure of how strong the radio wave is, which is actually the form in which the AM radio station is transmitting sound information.
The high-impedance earphone uses the diode's tiny charge deliveries to reproduce sound. The diaphragm inside the earphone moves back and forth as the amount of charge passing through the diode fluctuates up and down. Each time the radio wave increases in strength, the diaphragm moves in one direction. Each time the radio wave decreases in strength, the diaphragm moves in the other direction. Thus as the radio station varies the strength of its radio wave, the earphone's diaphragm moves back and forth and it reproduces the sound.
First, consider a wave traveling toward us on the surface of a lake. Suppose that this wave passes under a small boat and I ask you which way the wave is making the boat move. You would tell me that the boat is moving up and down. I would then tell you that the wave is vertically polarized because it causes objects that it encounters to move up and down rhythmically.
Unfortunately, pure water won't do for the next step because it won't support horizontally polarized waves. So let's imagine that some ecological disaster has turned the entire lake into gelatin. An explosion at the side of the lake now causes a wave to begin heading toward us on the gelatin lake, but this strange wave involves a side-to-side motion of the lake's surface. Now when the wave passes under the boat, the boat moves side-to-side rhythmically. In this case the wave is horizontally polarized because it causes objects that it encounters to move left and right rhythmically.
Now let's return to optics. When an electromagnetic wave heads toward us, its electric fields will push any electrically charged particles it encounters back and forth rhythmically. If we watch one of these charged particles as the wave passes it and observe that this particle moves up and down, then the wave is vertically polarized. If instead the charged particle moves left and right, then the wave is horizontally polarized.
Like all electromagnetic waves, radio waves and microwaves consist of coupled electric and magnetic fields that sustain one another in stable structures that move rapidly through empty space. Because an electromagnetic wave's electric field changes with time, it is able to create the wave's magnetic field and, because its magnetic field changes with time, that magnetic field is able to create the wave's electric field. Since they consist only of electric and magnetic fields, these waves cannot stay still—they must move (although you can trap them between mirrors so that they appear to stand in one place as they bounce back and forth). While they contain no true mass, they do contain energy and an electromagnetic wave carries energy from one place to another.
Electromagnetic waves are created whenever electrically charged particles change speed or direction; whenever they accelerate. Since there are accelerating electric charges everywhere—thermal energy keeps them moving about—there are also electromagnetic waves everywhere. But the radio waves used in communications systems are generated deliberately by moving electric charges back and forth. When charges are sent up and down a radio antenna, these charges are accelerating and they form complicated electric and magnetic fields that include electromagnetic waves. Once launched, those electromagnetic waves propagate through space at approximately the speed of light.
To send information with radio waves, a transmitter makes modifications in one or more the wave's characteristics. In an amplitude modulation scheme (AM), the transmitter changes the strength or "amplitude" of the wave to convey information—like sending radio smoke signals. In the frequency modulation scheme (FM), the transmitter changes the frequency of the wave to convey information—like whistling a tune with a complicated melody.
But heterodyne techniques have a side effect: they cause the radio receiver to emit radio waves. These waves originate with the local radio-frequency oscillator, and with other internal mixing frequencies such as the intermediate frequency oscillator present in many sophisticated receivers. Because these oscillators don't use very much power, the waves they emit aren't very strong. Nonetheless, they can be detected, particularly at short range. For example, it's possible for police to detect a radar detector that contains its own local microwave oscillator. Similarly, people who have tried to pirate microwave transmissions have been caught because of the microwaves emitted from their receivers. In WWII, the Japanese were apparently very successful at locating US forces by detecting the 455 kHz intermediate frequency oscillators in their radios—a problem that quickly led to a redesign of the radios to prevent that 455 kHz signal from leaking onto the antennas (thanks to Tom Skinner for pointing this out to me). As you can see, it is possible to track someone who is listening to the right type of radio receiver. However, the radio waves from that receiver are going to be very weak and you won't be able to follow them from a great distance.
The walls of your home are simply hard to look through. They block visible, infrared, and ultraviolet light nearly perfectly and that doesn't leave snoopers many good options. A person sitting outside your home with a thermal camera—a device that "sees" the infrared light associated with body-temperature objects—or a digital camera is going to have a nice view of your wall, not you inside. There are materials that, while opaque to visible light, are relatively transparent to infrared light, such as some plastics and fabrics. However, typical wall materials are too thick and too opaque for infrared light to penetrate. Sure, someone can put a camera inside your home and access it via an optical fiber or radio waves, but at that point, they might as well just peer through your window.
The only electromagnetic waves that penetrate walls well are radio waves, microwaves, and X rays. If someone builds an X ray machine around your home, they'll be able to see you, or at least your bones. Don't forget to wave. And, in principle, they could use the radar technique to look for you with microwaves, but you'd be a fuzzy blob at best and lost in the jumble of reflections from everything else in your home.
As for using a laser to monitor your conversations from afar, that's a real possibility. Surfaces vibrate in the presence of sound and it is possible to observe those vibrations via reflected light. But the technical work involved is substantial and it's probably easier to just put a bug inside the house or on its surface.
Since I first posted this answer, several people have pointed out to me that terahertz radiation also penetrates through some solid surfaces and could be used to see through the walls of homes. In fact, the whole low-frequency end of the electromagnetic spectrum (radio, microwaves, terahertz waves) can penetrate through electrically insulating materials in order to "observe" conducting materials inside a home and the whole high-frequency end of that spectrum (X-rays and gamma rays) can penetrate through simple atoms (low atomic number) in order to "observe" complex atoms inside a home. Still, these approaches to seeing through walls require the viewers to send electromagnetic waves through the house and those waves can be detected by the people inside. They're also not trivial to implement. I suppose that people could use ambient electromagnetic waves to see what's happening in a house, but that's not easy, either. Where there's a will, there's a way: stealth aircraft have been detected by way of the dark spot they produce in the ambient radio spectrum and the insides of the pyramids have been studied by looking at cosmic rays passing through them. Nonetheless, I don't think that many of us need worry about being studied through the walls of our homes.
The fact that light waves can travel in vacuum, and don't need any material to carry them, was disturbing to the physicists who first studied light in detail. They expected to find a fluid-like aether, a substance that was the carrier of electromagnetic waves. Instead, they found that those waves travel through truly empty space. One thing led to another, and soon Einstein proposed that the speed of light was profoundly special and that space and time were interrelated by way of that speed of light.
The Radio Home Page — Printer Friendly
The Complete Collection of Questions about Radio (4 prints, from oldest to newest) — Printer Friendly: